Unicable Problem OpenBh 5.2.007

Onkel

Member
My satellite configuration
2 LNB Astra/Hotdirb
multiswitch 9/8
Spaun SUS 21 FX (src 1076-1178)

I have problems when I can't record on one satellite not the other
use.

I've been using this configuration for ages and never had any problems.
if i use another image not obh everything works.

I load my file setting.

Thanks
 

Attachments

  • settings.rar
    960 bytes · Views: 4

Ev0

Admin
Staff member
Administrator
I don't use a mulitswitch, so not 100% sure this is your issue.

But you have set unicable matrix (switch) on lnb 1, but unicable Jess on lnb 2.

Set them both the same (i'm assuming switch / matrix is correct for your setup) and then see if the problem is resolved.
 

Onkel

Member
Thanks for your answer.
I've tried everything.

As has already been written above, with this configuration and other images, recording from another satellite works at the same time as what others are watching.

For example, I'm recording something on Hotbird and I can watch a channelin Hotbird, but I can't watch a channel from Astra.

I've been using blackhole for 10 years and openblackhole since openblackhole 4 I've had these problems.

Thanks
 

Attachments

  • Tuner A LNB1 Astra.jpg
    Tuner A LNB1 Astra.jpg
    346.8 KB · Views: 30
  • Tuner A LNB2 Hotbird.jpg
    Tuner A LNB2 Hotbird.jpg
    410.1 KB · Views: 30
  • Tuner B LNB1 Astra.jpg
    Tuner B LNB1 Astra.jpg
    397.7 KB · Views: 26
  • Tuner B LNB2 Hotbird.jpg
    Tuner B LNB2 Hotbird.jpg
    430.9 KB · Views: 27

Ev0

Admin
Staff member
Administrator
Maybe someone else that uses Matrix switch can help.

But to me, it seems wrong to use the same positions and userbands for both lnb's
 

Onkel

Member
spaun SUS have 2 frequencies 1076 and 1178

Tuner A use 1178 LNB1 is position 1
LNB2 is position 2

Tuner B use 1076
LNB1 position 1
LNB2 position 2

if I use preferred tuner A or B everything works but not Work for recording


When recording from a channel and changing to another satellite, the message "No tuner available"
 

Ev0

Admin
Staff member
Administrator
Can you post screenshots of the tuner setup, from an image you do not have this issue with ?
 

Onkel

Member
Hello Mister Evo i send you screenshots from not ObH image in this picture i have Unicable-matrix .

I can record and see something else no matter which satellite I turn on

in ObH no have this option

Thanks
 

Attachments

  • ObH Tuner 2 .jpg
    ObH Tuner 2 .jpg
    203.3 KB · Views: 16
  • ObH Tuner 1 .jpg
    ObH Tuner 1 .jpg
    378.8 KB · Views: 99
  • ObH Tuner .jpg
    ObH Tuner .jpg
    299.3 KB · Views: 15
  • Tuner B Hotbird .jpg
    Tuner B Hotbird .jpg
    269.9 KB · Views: 15
  • Tuner B Astra .jpg
    Tuner B Astra .jpg
    272.3 KB · Views: 13
  • Tuner A Hotbird .jpg
    Tuner A Hotbird .jpg
    253.4 KB · Views: 13
  • Tuner A Astra .jpg
    Tuner A Astra .jpg
    256.1 KB · Views: 12

Ev0

Admin
Staff member
Administrator
Hello Mister Evo i send you screenshots from not ObH image in this picture i have Unicable-matrix .

I can record and see something else no matter which satellite I turn on

in ObH no have this option

Thanks
As I said above, you are using a combination of Matrix and Jess with openbh.

In openatv you have used Matrix on both tuners and LNB settings.
 

Ev0

Admin
Staff member
Administrator
I can't select a UnicableMatrix with ObH.

If you would like to tell me which settings I should make...
The setting you have used here:
obh-tuner-1-jpg.4068
 

Onkel

Member
yes!!!!
With these settings, tuner A or B works without recording, both of them, but if I record something, it doesn't work
 

Onkel

Member
Hello Mister Evo today have time for test, have installed Openblackhole 4.4 and have setting tuner same image 5.2
i can recording channel to hotbird and can see channel to astra no have problem !!!!

Only problem image 5.2
 

Attachments

  • Tuner A Astra.jpg
    Tuner A Astra.jpg
    388.4 KB · Views: 12
  • Tuner A Hotbird.jpg
    Tuner A Hotbird.jpg
    408.2 KB · Views: 11
  • Tuner B Astra.jpg
    Tuner B Astra.jpg
    367.3 KB · Views: 8
  • Tuner B Hotbird.jpg
    Tuner B Hotbird.jpg
    418.7 KB · Views: 11

Ev0

Admin
Staff member
Administrator
I don't know what you have done, but everytime I look at the pictures of your tuners settings for OpenBh 5.2 they are different to what you show me you have in other images.

I suggest, do a factory reset (or reflash the box), then set the tuners up again fresh.
 

Onkel

Member
you can see to openblackhole 4.4 have setting sus 21 F my spaun unicable is sus 21 F and with 4.4 image work good recording and can see channel
image 5.2 i set sus 21 F have tuner failed set sus 21 F2 work

but where I've already written can't record and watch what others see at the same time

I've already flashed the box several times.

I don't want to bother you any further with my problem...
I then switched to an ATV, no problems with it.

Thank you for your help and support(y)
 

Ev0

Admin
Staff member
Administrator
you can see to openblackhole 4.4 have setting sus 21 F my spaun unicable is sus 21 F and with 4.4 image work good recording and can see channel
image 5.2 i set sus 21 F have tuner failed set sus 21 F2 work

but where I've already written can't record and watch what others see at the same time

I've already flashed the box several times.

I don't want to bother you any further with my problem...
I then switched to an ATV, no problems with it.

Thank you for your help and support(y)
The problem is not the image, it is that you are using different settings in openbh 5.2, compared to what you used in atv and obh 4.4

If you use the same correct settings in 5.2 then it will work.
 

Onkel

Member
I think the problem is Image but Set sus 21 f this work to Image 4.4 Set this to 5.2 tuner failed Set sus 21 f2 have picture astra and hotbird...
 

Ev0

Admin
Staff member
Administrator
I think the problem is Image but Set sus 21 f this work to Image 4.4 Set this to 5.2 tuner failed Set sus 21 f2 have picture astra and hotbird...

I have no idea which lnb you have.

Every screenshot you post, has different lnb options selected, but if it works in openbh 4.4 and atv then it will also work in 5.2 with the correct settings.

As you can see from the list below, there is no SUS 21 F2

Code:
        <manufacturer name="Spaun">
            <product name="SUS 21 F" positions="2" scrs="1076,1178"/>
            <product name="SUS 21 FI" positions="2" scrs="1210,1420"/>
            <product name="SUS 4441 F" scrs="1210,1420,1680,2040"/>
            <product name="SUS 5541 F-NFA" scrs="0974,1076,1178,1280"/>
            <product name="SUS 5581 F-NFA" scrs="0974,1076,1178,1280,1382,1484,1586,1688"/>
            <product name="SUS 5581 NF 1x8" scrs="1068,1284,1400,1516,1632,1748,1864,1980"/>
            <product name="SUS 5581 NF 3x3 1" scrs="1068,1284,1400"/>
            <product name="SUS 5581 NF 3x3 2" scrs="1516,1632,1748"/>
            <product name="SUS 5581 NF 3x3 3" scrs="1864,1980,2096"/>
            <product name="SUS 5581 NF Leg 1x8" scrs="0974,1076,1178,1280,1382,1484,1586,1688"/>
            <product name="SUS 5581 NF Leg 3x3 1" scrs="0974,1076,1178"/>
            <product name="SUS 5581 NF Leg 3x3 2" scrs="1280,1382,1484"/>
            <product name="SUS 5581 NF Leg 3x3 3" scrs="1586,1688,1790"/>
            <product name="SUS 5581 NFA Leg 1x8" scrs="0974,1076,1178,1280,1382,1484,1586,1688"/>
            <product name="SUS 5581 NFA Leg 3x3 1" scrs="0974,1076,1178"/>
            <product name="SUS 5581 NFA Leg 3x3 2" scrs="1280,1382,1484"/>
            <product name="SUS 5581 NFA Leg 3x3 3" scrs="1586,1688,1790"/>
            <product name="SUS 41 F" positions="4" format="jess" scrs="1076,1178,1280,1382"/>
            <product name="SUS 41 F2" positions="4" scrs="1076,1178,1280,1382"/>
            <product name="SUS 41 F3" positions="4" format="jess" scrs="1076,1178,1280,1382"/>
            <product name="SUS 9942/8 NF Leg 2x4" positions="2" scrs="1076,1178,1280,1382"/>
        </manufacturer>


If you post your settings file (found in /etc/enigma2) from both your openbh 4.4 image and your 5.2 image then I can try and fix the problem for you.
 

Onkel

Member
i have 2 quattro lnb this is connect to 9/16 multiswitch and the spaun sus 21 F is connect to multiswitch this have 10 year and all blackhole an openblackhole 4.4 work.
i will you send the setting in etc/enigma for 4.4 and 5.2
Ok thanky you for Help and sorry a stress you with my Problem.....(y)
 

Onkel

Member
Hello Mister Evo i send you Settings

Settings-File 4.4.023 ------> Work
Settings File-5.0.013-------> Work
Settings File-5.1.012-------> Work
Settings File-5.2.007-------> Not Work

image I imported cleanly do not use multiboot

Thanks for Help
 

Attachments

  • Settings.rar
    3.9 KB · Views: 1
Top