Problem setting up tuner at SCR(Unicable/JESS)

Akita

Akita

Active member
Have set according to picture but when I then save it shows
Set: 3.0E, 0.8W.
No picture is shown on TV.
How do I remove 3.0E.
Shouldn't it just say 0.8W.
Then at slot B it shows Set: 19.2E, 19.4E, 0.8W.
What does 19.2E, 19.4E come from?
Is there a way to reset/delete all tuner settings so I can program again.
 

Attachments

  • A.jpg
    A.jpg
    77.2 KB · Views: 11
  • B.jpg
    B.jpg
    75.4 KB · Views: 11
can you please post more details of your satellite setup, fixed dish, with multiple LNB's, several satellite dishes, motorized dish.
Make/Model of your receiver?
Which image, version?
 
Mick12334 said:
can you please post more details of your satellite setup, fixed dish, with multiple LNB's, several satellite dishes, motorized dish.
Make/Model of your receiver?
Which image, version?
Click to expand...
VU+ duo 4k se
A satellite dish.
No motor control.
A microwave head GT-SAT model GT-S3DCSS24.
An output SCR (Unicable/JESS) and 3 regular LNBs.
As I showed in the picture, there are two satellites.
I should only have 0.8W.
I have tried to delete 3.0E but it appears again.
 
Have you tried the basic setup, trying to get 1 satellite?

Do you have 3 cable runs, from the regular LNB's, or are you using a Diseqc switch?

If you set the tuner to off, reboot your receiver, then set just one tuner, using the single tuner option, and mo the advanced setup, but this depends on how you've got all the LNB's connected to your receiver, separate cable runs, diseqc switch, or other system?
 
I only have one cable to the tuner.
I have tried as you said.
Deactivated and deleted according to the instructions in OpenBh.
Restarted and went in and selected SCR(Unicable/JESS) and then my setting for 0.8W that I previously entered is displayed.
Why is this when the satellites are deleted.
Saves and then more satellites appear in the menu. (3.0E end 0.8W)
Something must be wrong with the deletion.
For tuner B I have not selected 19.2E, 19.4E but they still appear.
How do I delete all my tuner settings so that I can program
from scratch.
 
Now that this doesn't work, I can go in and delete the "settings" file.
Now it's in several places.
In which directory is "default-settings" located where I should change it?
 
In the tuner menu, where it shows 0.8W, highlight that, then press left or right until you get to 3.0E and then disable that satellite (change the lnb to not configured).

Then scroll back to 0.8W and save.

As for 19.2E and 19.4E this comes from the satellites.xml file that you have loaded onto your box.
 
Thanks.
Now there is only 0.8W but there is no picture.
When I then exit, it appears on the Vu+ menu "DVB service"
What is wrong?
 
Last edited:
Akita said:
Thanks.
Now there is only 0.8W but there is no picture.
When I then exit, it appears on the Vu+ menu "DVB service"
What is wrong?
Click to expand...
Sounds like you have loading some 3rd party settings file and messed with the config.

Just do a channel scan on 0.8w
 
The strange thing was that when I first selected the setting, a channel was shown.
Then I continued with Tuner B and C etc.
That's when the channels disappeared and the strange thing was that other satellite positions appeared.
Now nothing works?
Did a chan and no channels were found.
 
Akita said:
VU+ duo 4k se
A satellite dish.
No motor control.
A microwave head GT-SAT model GT-S3DCSS24.
An output SCR (Unicable/JESS) and 3 regular LNBs.
As I showed in the picture, there are two satellites.
I should only have 0.8W.
I have tried to delete 3.0E but it appears again.
Click to expand...
You state that you have 1xS2x LNB, and 3 other ordinary LNB's? Are these all connected to satellite dishes, and your receiver? If so you must have be using a Diseqc switch, if not then you must have the single output SCR LNB connected directly to your receiver with your satellite dish pointing at 0.8W.

Try going into the menu, Tuner Setup, Signal finder, and testing some transponders:
Code: 
https://www.lyngsat.com/Thor-5-6-7-and-Intelsat-10-02.html
 
Kanske borde jag avaktivera A och ansluta kabeln till tuner B och testa.
Mick12334 said:
You state that you have 1xS2x LNB, and 3 other ordinary LNB's? Are these all connected to satellite dishes, and your receiver? If so you must have be using a Diseqc switch, if not then you must have the single output SCR LNB connected directly to your receiver with your satellite dish pointing at 0.8W.

Try going into the menu, Tuner Setup, Signal finder, and testing some transponders:
Code: 
https://www.lyngsat.com/Thor-5-6-7-and-Intelsat-10-02.html
Click to expand...
I have two receivers.
Vu+ duo 2 which is connected with the old type of LNB.
3 connections.
Vu+ do 4K se connected only with a cable from the microwave head SCR (Unicable/JESS).
 
Very strange things have happened.
All my channels have disappeared.
Copied them again but no signal comes in.
Maybe the only thing to do is to do a Fatory Reset and reinstall.
What does a Fatory reset do?
 
I had a regular LNB microwave head before.
Can I use the channel settings for my new SCR(Unicable/JESS) microwave head?
After copying my channel settings, info about the channel is displayed and also that turner A is visible at the bottom right.
No signal strength is displayed.
 
Have you tried doing a blind scan?

You could try one of your regular LNB's, on that dish, and/or try your Duo 4K on the other other dish setup, just to rule some things out.
 
You must log in or register to reply here.
Back
Top